[OpenWrt Wiki] AVM FRITZ!Box 7362 SL (2024)

Photo of front of the casing

Photo of back of the casing

Photo of side of the casing

Photo of PCB (Top)

Photo of PCB (Bottom)

The Fritzbox generates some acoustical noise from internal switching power supply circuits, especially remarkable at boot time.Using the original AVM Fritzbox firmware the noise disappears after 30 seconds, however if you use Openwrt firmware, the noise stays. This might annoy people who want install that device in some quite place like the sleeping room.One solution is to add a 1kΩ...3.3kΩ resistor on the pcb to the analouge telefony part (under the shown electrolytic capacitor, see picture below), giving the circuit some load, and then the noise is gone. The resistor slightly increases the power consumption (up to 0.9W depending on the resistor) of the router.

Assumption: As the Openwrt firmware of the 7362SL doen´t support the telefony part (yet), maybe the telefony circuit isn´t set to a specific state as the AVM firmware does it. Adding the resistor is a hardware-workaround.

Telefony part, location of electrolytic capacitor

Resistor soldered to the pins of the electrolytic capacitor

Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

Seen from the rear of the device, the most right of the 4 holes is square cut while the others are round.

Insert photo of PCB with markings

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

ROM VER: 1.1.4CFG 05Ā▒CဌEDD4C[\](AVM) EVA Revision: 1.1964 Version: 2964(C) Copyright 2005 AVM Date: Nov 8 2013 Time: 15:45:15 (0) 3 0x0-0x740D[FLASH:] MACRONIX Uniform-Flash 1MB 256 Bytes WriteBuffer[FLASH:](Eraseregion [0] 16 sectors a 64kB)[NAND:] 128MB MICRON 2048 Pagesize 128k Blocksize 1024 Blocks 8Bit 1 CS HW[SYSTEM:] VR9 on 500MHz/250MHz/250MHz.Atheros 8030/35 detectedEva_AVM >##....................................Lantiq xDSL CPE VR9[ 0.000000] Linux version 2.6.32.61 (hjortmann@EmbeddedVM) (gcc version 4.8.1 (Buildroot 2013.05) ) #1 SMP Tue May 5 11:31:15 CEST 2015[ 0.000000] phym = 08000000, mem = 08000000, max_pfn = 00008000[ 0.000000] Reserving memory for CP1 @0xa8000000, size 0x00000000[ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 806c6000)[ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry[ 0.000000] bootconsole [early0] enabled[ 0.000000] CPU revision is: 00019556 (MIPS 34Kc)[ 0.000000] Determined physical RAM map:[ 0.000000] Initrd not found or empty - disabling initrd[ 0.000000] Zone PFN ranges:[ 0.000000] Normal 0x00000000 -> 0x00008000[ 0.000000] Movable zone start PFN for each node[ 0.000000] early_node_map[1] active PFN ranges[ 0.000000] 0: 0x00000000 -> 0x00008000[ 0.000000] [module-alloc-by-name] 'modulemem' not in use, use AVM Kernel Config (8675328 bytes, reserved for module mem)[ 0.000000] [module-alloc] use 0x846000 bytes at 0x81101000[ 0.000000] 1 available secondary CPU TC(s)[ 0.000000] PERCPU: Embedded 7 pages/cpu @8194b000 s5760 r8192 d14720 u65536[ 0.000000] pcpu-alloc: s5760 r8192 d14720 u65536 alloc=16*4096[ 0.000000] pcpu-alloc: [0] 0 [0] 1[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512[ 0.000000] Kernel command line: console=ttyS0,115200n8r nor_size=0MB sflash_size=1024KB nand_size=128MB ethaddr=08:96:D7:3D:9A:C0[ 0.000000] [NAND] nand_size = 0x8000000[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)[ 0.000000] wait instruction: r4k_wait_irqoff[ 0.000000] [avm_cache_set_coherency]: setting cache coherency for HWRevision=203 to write back allocate[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes[ 0.000000] Writing ErrCtl register=0007f543[ 0.000000] Readback ErrCtl register=0007f543[ 0.000000] Memory: 113548k/131072k available (4744k kernel code, 17340k reserved, 2187k data, 212k init, 0k highmem)[ 0.000000] Hierarchical RCU implementation.[ 0.000000] NR_IRQS:181[ 0.000000] [mips_cpu_irq_init] irq_base 0[ 0.000000] SRSConf0 0x3feffbfe: SRS1: 0xffffffff, SRS2 0xffffffff, SRS3 0xffffffff[ 0.000000] Console: colour dummy device 80x25[ 0.000000] console [ttyS0] enabled, bootconsole disabled[ 0.000000] console [ttyS0] enabled, bootconsole disabled[ 0.020000] Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976)[ 0.240000] Security Framework initialized[ 0.240000] Mount-cache hash table entries: 512[ 0.250000] kernel_init: started[ 0.250000] kernel_init: kernel locked[ 0.250000] Limit of 2 TCs set[ 0.250000] TLB of 32 entry pairs shared by 2 VPEs[ 0.250000] VPE 0: TC 0, VPE 1: TC 1[ 0.250000] IPI buffer pool of 8 buffers[ 0.260000] CPU revision is: 00019556 (MIPS 34Kc)[ 0.490000] TC 1 going on-line as CPU 1[ 0.500000] Brought up 2 CPUs[ 0.510000] [yield_context_init] cpu=1 tc=2 mask=300[ 0.510000] [yield_context_init] cpu=0 tc=3 mask=410[power_managment_setup] reset 'DSL, DFE, AFE, VOICE, DSLTC, ARC'[power_managment_setup] reset 'LDO'[power_managment_setup] power down 'PPE TC, PPE EMA, LEDC, DFEV1, DFEV0'[power_managment_setup] power down 'MSI1, PDI1 PCIE1 PCIE1_PHY'[power_managment_setup] power down 'USB CTRL'[power_managment_setup] power down 'GPHY'[power_managment_setup] disable power domain 'DSL + DFE'[final_setup_dcdc] start*((volatile unsigned char *)0xBF106A17) = 0x5A;*((volatile unsigned char *)0xBF106A18) = 0x46;*((volatile unsigned char *)0xBF106A11) = 0x13;*((volatile unsigned char *)0xBf106a00) = 0;*((volatile unsigned char *)0xBf106a01) = 0;*((volatile unsigned char *)0xBf106a02) = 0xFF;*((volatile unsigned char *)0xBf106a03) = 0xE6;*((volatile unsigned char *)0xBf106a04) = 0;*((volatile unsigned char *)0xBf106a05) = 0x1B;*((volatile unsigned char *)0xBf106a15) = 0x8b;*((volatile unsigned char *)0xBf106a17) = 0x80;*((volatile unsigned char *)0xBf106a18) = 0x28;*((volatile unsigned char *)0xBf106a06) = 0x52;[final_setup_dcdc] done[ 0.620000] NET: Registered protocol family 16[ 0.620000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2013 Lantiq Deutschland GmbH[ 0.630000] Reboot Status is: Power-On[ 0.630000] [avmnet] [avmnet_cfg_init] Driver version: 6.136 - Revision 1496:2706 - Di 5. Mai 11:30:48 CEST 2015[ 0.950000] Lantiq PCIe Root Complex driver, version 2.0.0, (c) 2001-2013 Lantiq Deutschland GmbH[ 0.960000] bio: create slab <bio-0> at 0[ 0.960000] ifx_pcie_rc_class_early_fixup port 0: fixed pcie host bridge to pci-pci bridge[ 0.970000] pci 0000:00:00.0: PME# supported from D0 D3hot[ 0.970000] pci 0000:00:00.0: PME# disabled[ 0.980000] pci 0000:01:00.0: PME# supported from D0 D1 D3hot[ 0.980000] pci 0000:01:00.0: PME# disabled[ 0.990000] pci 0000:00:00.0: PCI bridge, secondary bus 0000:01[ 0.990000] pci 0000:00:00.0: IO window: disabled[ 1.000000] pci 0000:00:00.0: MEM window: 0x1c000000-0x1c0fffff[ 1.000000] pci 0000:00:00.0: PREFETCH window: 0x1c100000-0x1c1fffff[ 1.010000] NET: Registered protocol family 8[ 1.010000] NET: Registered protocol family 20[ 1.020000] NET: Registered protocol family 2[ 1.020000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)[ 1.020000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)[ 1.020000] TCP bind hash table entries: 4096 (order: 4, 81920 bytes)[ 1.030000] TCP: Hash tables configured (established 4096 bind 4096)[ 1.050000] TCP reno registered[ 1.050000] NET: Registered protocol family 1[ 1.060000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17 ,(c)2009 Infineon Technologies AG[ 1.060000] skb_shared_size:344[ 1.070000] Lantiq CGU driver, version 1.1.32, (c) 2001-2013 Lantiq Deutschland GmbH[ 1.080000] squashfs: version 3.4 (2008/08/26) Phillip Lougher[ 1.080000] fuse init (API version 7.13)[ 1.090000] msgmni has been set to 222[ 1.090000] io scheduler noop registered (default)[ 1.100000] [avm_membench_init][ 1.350000] avm_net_trace: Up and running.[ 1.360000] [loadcontrol] set auto - scale=1[ 1.360000] [avm] configured: watchdog event debug[ 1.370000] AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: May 5 2015 11:30:17)[ 1.380000] ifx_pmu_init: Major 247[ 1.380000] Lantiq PMU driver, version 1.2.6, (c) 2001-2013 Lantiq Deutschland GmbH[ 1.390000] Infineon Technologies RCU driver version 1.0.7[ 1.390000] Lantiq Thermal Sensor driver, version 1.0.3, (c) 2001-2013 Lantiq Deutschland GmbH[ 1.400000] ttyS0 at MMIO 0x1e100c00 (irq = 107) is a PORT_IFX_ASC[ 1.420000] loop: module loaded[ 1.420000] nbd: registered device at major 43[ 1.440000] Generic platform RAM MTD, (c) 2004 Simtec Electronics[ 1.440000] Platform NOR MTD, (c) AVM 2010[ 1.440000] [HSNAND] Hardware-ECC activated[ 1.450000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron NAND 128MiB 3,3V 8-bit)[ 1.460000] Scanning device for bad blocks[ 1.550000] Creating 6 MTD partitions on "ifx_hsnand":[ 1.550000] 0x000000000000-0x000000400000 : "kernel"[ 1.560000] {ifx_mtd_add_notifier} name kernel[ 1.560000] 0x000000400000-0x000003400000 : "filesystem"[ 1.570000] {ifx_mtd_add_notifier} name filesystem[ 1.570000] 0x000003400000-0x000003800000 : "reserved-kernel"[ 1.580000] {ifx_mtd_add_notifier} name reserved-kernel[ 1.580000] 0x000003800000-0x000006800000 : "reserved-filesystem"[ 1.590000] {ifx_mtd_add_notifier} name reserved-filesystem[ 1.590000] 0x000006800000-0x000006a00000 : "config"[ 1.600000] {ifx_mtd_add_notifier} name config[ 1.600000] 0x000006a00000-0x000008000000 : "nand-filesystem"[ 1.610000] {ifx_mtd_add_notifier} name nand-filesystem[ 1.610000] Lantiq SSC driver, version 2.4.1, (c) 2001-2013 Lantiq Deutschland GmbH[ 1.620000] Creating 3 MTD partitions on "ifx_sflash":[ 1.630000] 0x000000000000-0x000000040000 : "urlader"[ 1.630000] {ifx_mtd_add_notifier} name urlader[ 1.640000] 0x000000040000-0x0000000a0000 : "tffs (1)"[ 1.640000] {ifx_mtd_add_notifier} name tffs (1)[ 1.650000] 0x0000000a0000-0x000000100000 : "tffs (2)"[ 1.650000] {ifx_mtd_add_notifier} name tffs (2)[ 1.660000] Lantiq SPI flash driver, version 1.1.9, (c) 2001-2013 Lantiq Deutschland GmbH[ 1.660000] tun: Universal TUN/TAP device driver, 1.6[ 1.670000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>[ 1.680000] IFX SWITCH API, Version 1.1.8.5[ 1.680000] SWAPI: Registered character device [switch_api] with major no [81][ 1.690000] Switch API: PCE MicroCode loaded !![ 1.690000] res = 8792a500[ 1.690000] i2c /dev entries driver[ 1.700000] CAPI Subsystem Rev 1.1.2.8[ 1.700000] AVM PA 4.3.10 2014-09-21[ 1.700000] AVM PA skb pktinfo at offset 128 size 196[ 1.710000] [loadcontrol]module avm_pa registered[ 1.710000] IPv4 over IPv4 tunneling driver[ 1.720000] TCP cubic registered[ 1.720000] mcfw: IGMPv3 fast forwarding[ 1.730000] NET: Registered protocol family 10[ 1.730000] IPv6 over IPv4 tunneling driver[ 1.740000] NET: Registered protocol family 17[ 1.740000] NET: Registered protocol family 8[ 1.740000] atmpvc_init() failed with -17[ 1.750000] KOAM is loaded successfully.[ 1.750000] l2tp_core: L2TP core driver, V2.0[ 1.760000] l2tp_ip: L2TP IP encapsulation support (L2TPv3)[ 1.760000] l2tp_netlink: L2TP netlink interface[ 1.770000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)[ 1.770000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)[ 1.780000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>[ 1.780000] All bugs added by David S. Miller <davem@redhat.com>[ 1.790000] <ifx_fix_timing>[ 1.800000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0)[ 1.800000] mount on mtd7 and mtd8 (double buffering)[ 1.810000] Adam2 environment variables API installed.[ 1.810000] [simple-profiling]: 2 performance counters implemented, NEW_34K[ 1.820000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable)[ 1.830000] Setup tcs=0x1 current_tc_mask=0x1, reg=0[ 1.840000] [simple-profiling]: 2 performance counters implemented, NEW_34K[ 1.850000] Enable Performance Counter 1 for Data cache load/store misses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable)[ 1.860000] Setup tcs=0x1 current_tc_mask=0x1, reg=1[ 1.870000] AVM Simple Profiling enabled Version 3.0[ 1.870000] {avmnet_cfg_netinit}[ 1.870000] [avmnet] No config found for HWRev 203, HWSubRev 1, Profile-ID 0, trying base config for HWSubRev[ 1.880000] [avmnet] No config found for HWRev 203, HWSubRev 1, trying base config for HWRev[ 1.890000] [avmnet] [avmnet_swi_7port_init] Init on module swi_vr9 called.[ 2.320000] Loading AVM Net Common Datapath Driver for 7Port Switch......[ 2.320000] [ppe_eth_init] init_hw()[ 2.330000] [init_hw] ppe_hw_init=0xff successful[ 2.330000] [ppe_eth_init] ifx_proc_file_create()[ 2.340000] [ppe_eth_init] dma_setup_init()[ 2.350000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown unicast frames 0x68[ 2.360000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown multicast frames 0x68[ 2.460000] [avmnet] [avmnet_links_port_update] Maximum port number 0 exceeded with 2![ 2.470000] [avm_event_source_trigger]: not registered[ 2.470000] [avmnet] [avmnet_links_port_update] Maximum port number 0 exceeded with 2![ 5.130000] [avm_pa_multiplexer_init] start[ 5.140000] [avm_pa_multiplexer_init] init complete[ 5.140000] [avm_pa_multiplexer_register_instance][ 5.140000] add:avmnet_7port_pce_add_session+0x0/0x5a0[ 5.140000] remove:avmnet_7port_pce_remove_session+0x0/0x80[ 5.170000] kernel_init: basic setup done[ 5.170000] SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock1[ 5.180000] yaffs: dev is 32505857 name is "mtdblock1" ro[ 5.180000] yaffs: passed flags ""[ 5.210000] VFS: Mounted root (yaffs filesystem) readonly on device 31:1.[ 5.210000] Freeing unused kernel memory: 212k freed[ 5.260000] trying /sbin/init[ 5.310000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2d83)[ 5.320000] {ifx_hsnand_read_page_hwecc} page 0x2d83 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 5.370000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x813)[ 5.380000] {ifx_hsnand_read_page_hwecc} page 0x813 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 5.400000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x824)[ 5.400000] {ifx_hsnand_read_page_hwecc} page 0x824 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 5.450000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2e2c)[ 5.460000] {ifx_hsnand_read_page_hwecc} page 0x2e2c Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 5.510000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x868)[ 5.520000] {ifx_hsnand_read_page_hwecc} page 0x868 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 5.550000] [squashfs] use zip compression[ 5.590000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x9e7)[ 5.590000] {ifx_hsnand_read_page_hwecc} page 0x9e7 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 5.660000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xa68)[ 5.670000] {ifx_hsnand_read_page_hwecc} page 0xa68 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 5.690000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xa88)[ 5.700000] {ifx_hsnand_read_page_hwecc} page 0xa88 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 5.810000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1564)[ 5.810000] {ifx_hsnand_read_page_hwecc} page 0x1564 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 5.870000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xa05)[ 5.880000] {ifx_hsnand_read_page_hwecc} page 0xa05 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 5.890000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xa17)[ 5.900000] {ifx_hsnand_read_page_hwecc} page 0xa17 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[VR9-flash] -- Test --starting pid 147, tty '/dev/tty[ 5.960000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xcce)[ 5.970000] {ifx_hsnand_read_page_hwecc} page 0xcce Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-BiterrorS0': '/etc/init.d/rc.S'mount: mounting proc on /proc failed: Device or resource busytar: removing leading '/' from member namessource files in group 0 .../etc/init.d/S00-signal /etc/init.d/S05-watchdog /etc/init.d/S09-rtc/etc/init.d/S01-head /etc/init.d/S08-tffs/etc/init.d/S02-led /etc/init.d/S09-config[ 6.180000] TFFS Name Table K[config-space] detected mtdmtd4: size '2097152'modprobe: module nand not found in modules.dep[config-space][yaffs] driver is loaded[config-space] using mtd4 for /var/flash[ 6.280000] yaffs: dev is 32505860 name is "mtdblock4" rw[ 6.290000] yaffs: passed flags ""[config-space] /var/flash assigned @ /dev/mtdblock4[ 6.890000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xe1c)[ 6.900000] {ifx_hsnand_read_page_hwecc} page 0xe1c Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.020000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xf2f)[ 7.030000] {ifx_hsnand_read_page_hwecc} page 0xf2f Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.090000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xdda)[ 7.100000] {ifx_hsnand_read_page_hwecc} page 0xdda Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.150000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1666)[ 7.160000] {ifx_hsnand_read_page_hwecc} page 0x1666 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.200000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1119)[ 7.200000] {ifx_hsnand_read_page_hwecc} page 0x1119 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.250000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x160f)[ 7.260000] {ifx_hsnand_read_page_hwecc} page 0x160f Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.350000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xdb4)[ 7.350000] {ifx_hsnand_read_page_hwecc} page 0xdb4 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.590000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x261b)[ 7.600000] {ifx_hsnand_read_page_hwecc} page 0x261b Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.610000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2625)[ 7.620000] {ifx_hsnand_read_page_hwecc} page 0x2625 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.670000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x16ae)[ 7.680000] {ifx_hsnand_read_page_hwecc} page 0x16ae Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.710000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x16d8)[ 7.710000] {ifx_hsnand_read_page_hwecc} page 0x16d8 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.740000] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1707)[ 7.750000] {ifx_hsnand_read_page_hwecc} page 0x1707 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 7.770000] [module-alloc-by-name] give 0x1a000 bytes at 0x81101000 to module 'led_modul_Fritz_Box_HW203' (0x82c000 bytes left)[ 7.790000] led_modul_Fritz_Box_HW203: module license '[ 7.790000] (C) Copyright 2012 by AVM[ 7.790000] ' taints kernel.[ 7.800000] Disabling lock debugging due to kernel taint[ 7.830000] [LED] use GPIO 32 for 'gpio_avm_led_power'[ 7.830000] [LED] use GPIO 38 for 'gpio_avm_led_internet'[ 7.840000] [LED] use GPIO 35 for 'gpio_avm_led_dect'[ 7.840000] [LED] use GPIO 36 for 'gpio_avm_led_wlan'[ 7.850000] [LED] use GPIO 47 for 'gpio_avm_led_info'[ 7.850000] [LED] use GPIO 34 for 'gpio_avm_led_info_red'[ 7.860000] [BUTTON] use GPIO 29 for 'gpio_avm_button_wlan'[ 7.860000] [BUTTON] use GPIO 1 for 'gpio_avm_button_dect'[ 7.870000] [register_bug_debug_table] name='led-modul' 0x8110de24 - 0x8110de38[ 7.890000] AVM_WATCHDOG: System Init UEberwachung 120 SekundenP-Defaults: do nothing[ 8.200000] [module-alloc-by-name] give 0x2000 bytes at 0x8111b000 to module 'rtc_avm' (0x82a000 bytes left)[ 8.230000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0[ 8.230000] [avm-rtc]: avm_rtc_probe: register: ret=0x87332c00[ 8.240000] [avm-rtc]: avm_rtc_probe: successexceute files in group 0 .../etc/init.d/E05-basemodulesgroup 0 done ...source files in group 1 .../etc/init.d/S10-html /etc/init.d/S12-default/etc/init.d/S10-vm /etc/init.d/S15-filesys/etc/init.d/S11-config_def /etc/init.d/S17-capi/etc/init.d/S11-piglet /etc/init.d/S17-tam[ 8.430000][ 8.430000] [avm_debug] redirecting kernel-messages (/dev/debug)[ 8.460000][0] [module-alloc-by-name] give 0xd000 bytes at 0x8111d000 to module 'Piglet_noemif' (0x81d000 bytes left)[ 8.460000][0] [module-alloc-by-name] 0xd000 bytes used, 0xeb80 bytes expected[ 8.480000][0] [piglet]use default-settings (1 gpio from hw_config)[ 8.510000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1f0c)[ 8.510000][0] {ifx_hsnand_read_page_hwecc} page 0x1f0c Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 8.530000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1f33)[ 8.530000][0] {ifx_hsnand_read_page_hwecc} page 0x1f33 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 8.560000][0] patch_dectfw: c0193000, totallen = 44879(af4f)[ 8.560000][0] patch_dectfw: patch_adress: a0 max_len: 26 with Version 2 Len: 17[ 8.560000][0] patch_dectfw: dectmode 1[ 8.560000][0] dect_loader: slow-bootmode**********************************************[ 10.660000][0] [0]system-load 2 loadavg 0.23 0.5 0.2 - 38 tasks:77 % curr:modprobe(19 %) max:init(49 %, pid:1), readytorun: 1, pgfault 994/s (max 1 avg 0.9)******************************************[ 11.640000][0] dect144xx_file_process: upload of '/lib/modules/dectfw_secondlevel_441.hex' successfull[ 13.750000][0] [piglet]TDM: FS: 8005 Hz CLK: 1023995 Hzmodprobe: module nand not found in modules.dep[yaffs] driver is loaded[yaffs] nand-mtd: mtd5: 01600000 00020000 "nand-filesystem"[ 13.870000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xb95)[ 13.870000][0] {ifx_hsnand_read_page_hwecc} page 0xb95 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 13.970000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xc70)[ 13.970000][0] {ifx_hsnand_read_page_hwecc} page 0xc70 Sector 0 0 Biterror 0 OOB-Biterror 1 ECC-Biterror[ 13.970000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xc79)[ 13.970000][0] {ifx_hsnand_read_page_hwecc} page 0xc79 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 14.060000][1] yaffs: dev is 32505861 name is "mtdblock5" rw[ 14.060000][1] yaffs: passed flags ""[yaffs] Internal Memory assigned @ /var/media/ftp[Internal Memory] is NOT empty.start_indexation.mp3BilderDokumenteFRITZMusikVideos[Internal Memory] initially filling skipped[ 14.230000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1735)[ 14.230000][0] {ifx_hsnand_read_page_hwecc} page 0x1735 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 14.280000][1] [module-alloc-by-name] give 0x66000 bytes at 0x8112a000 to module 'pcmlink' (0x7b7000 bytes left)[ 14.280000][1] [module-alloc-by-name] 0x66000 bytes used, 0x65db8 bytes expected[pcmlink]svn: 2091[ 14.490000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1a21)[ 14.500000][0] {ifx_hsnand_read_page_hwecc} page 0x1a21 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 14.540000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1a55)[ 14.540000][0] {ifx_hsnand_read_page_hwecc} page 0x1a55 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 14.560000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1a7e)[ 14.560000][0] {ifx_hsnand_read_page_hwecc} page 0x1a7e Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 14.600000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1ab9)[ 14.600000][0] {ifx_hsnand_read_page_hwecc} page 0x1ab9 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 14.630000][1] [module-alloc-by-name] give 0xdb000 bytes at 0x81190000 to module 'isdn_fbox_fon5' (0x6dc000 bytes left)[ 14.630000][1] [module-alloc-by-name] 0xdb000 bytes used, 0xdd72c bytes expected[isdn]svn:3113avm_stack_attach: cpu1 -> cpu1[ 15.170000][1] driver params overwritten io_addr=0x0 irq_num=0lavm_stack_attach_oncpu: cpu1[ 15.170000][1] [pcmlink]chrony-supportPCMLINK: Version 4.209 Codecslots=6 Slics=1 Pots=1 TE=0 NT=0 DECT=4 (IA3222)no HwCross DSP-EC: 0[ 15.420000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1964)[ 15.420000][0] {ifx_hsnand_read_page_hwecc} page 0x1964 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 15.430000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1968)[ 15.430000][0] {ifx_hsnand_read_page_hwecc} page 0x1968 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 15.440000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1984)[ 15.440000][0] {ifx_hsnand_read_page_hwecc} page 0x1984 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 15.490000][0] [module-alloc-by-name] give 0x69000 bytes at 0x8126b000 to module 'capi_codec' (0x673000 bytes left)[ 15.490000][0] [module-alloc-by-name] 0x69000 bytes used, 0x6a4d8 bytes expectedcapicodec_init()[capi_codec] support fax[capi_codec] support Codecs[ 15.660000][1] [module-alloc-by-name] give 0x44000 bytes at 0x812d4000 to module 'avm_dect' (0x62f000 bytes left)[ 15.660000][1] [module-alloc-by-name] 0x44000 bytes used, 0x46008 bytes expected[DECTDRV_ERR] avm_dect driver init[DECTDRV_ERR] [avm_dect]avm_dect_thread: start[ 15.720000][1] [module-alloc-by-name] give 0x4000 bytes at 0x81318000 to module 'dect_io' (0x62b000 bytes left)[ 15.720000][1] [module-alloc-by-name] 0x4000 bytes used, 0x483c bytes expectedTAM: create directory /data/tamexceute files in group 1 .../etc/init.d/E15-devicemknod led c 242mknod tffs c 243mknod avm_power c 253mknod debug c 249mknod avm_event c 251mknod capi_oslib c 68mknod dect_io c 227/group 1 done ...source files in group 2 .../etc/init.d/S21-udevexceute files in group 2 ...group 2 done ...source files in group 3 .../etc/init.d/S30-ledcfgexceute files in group 3 ...group 3 done ...source files in group 4 ...[ 16.080000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2453)[ 16.080000][0] {ifx_hsnand_read_page_hwecc} page 0x2453 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror/etc/init.d/S42-ptest /etc/init.d/S46-usb/etc/init.d/S44-hostname /etc/init.d/S48-configdJan 1 01:00:16 udevd[435]: specified group 'tty' unknownJan 1 01:00:16 udevd[435]: specified group 'dialout' unknownJan 1 01:00:16 udevd[435]: specified group 'kmem' unknownJan 1 01:00:16 udevd[435]: specified group 'video' unknownJan 1 01:00:16 udevd[435]: specified group 'audio' unknownJan 1 01:00:16 udevd[435]: specified group 'lp' unknownJan 1 01:00:16 udevd[435]: specified group 'disk' unknownJan 1 01:00:16 udevd[435]: specified group 'floppy' unknownJan 1 01:00:16 udevd[435]: specified group 'cdrom' unknownJan 1 01:00:16 udevd[435]: specified group 'tape' unknown[ 16.380000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1ba5)[ 16.380000][0] {ifx_hsnand_read_page_hwecc} page 0x1ba5 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 16.400000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1bc8)[ 16.400000][0] {ifx_hsnand_read_page_hwecc} page 0x1bc8 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 16.440000][1] [module-alloc-by-name] give 0x2a000 bytes at 0x8131c000 to module 'usbcore' (0x601000 bytes left)[ 16.440000][1] [module-alloc-by-name] 0x2a000 bytes used, 0x2a83c bytes expected[ 16.590000][1] usbcore: registered new interface driver usbfs[ 16.590000][1] usbcore: registered new interface driver hub[ 16.590000][1] usbcore: registered new device driver usb[ 16.770000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1c2c)[ 16.770000][0] {ifx_hsnand_read_page_hwecc} page 0x1c2c Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 16.790000][0] [module-alloc-by-name] give 0x1c000 bytes at 0x81346000 to module 'ifxusb_host' (0x5e5000 bytes left)[ 16.790000][0] [module-alloc-by-name] 0x1c000 bytes used, 0x1e29c bytes expected[ 16.820000][0] IFXUSB: ifxusb_hcd: version 3.0alpha B100312[ 16.820000][0] Chip Version :000b BurstSize=4[ 16.820000][0] early VBUS switch[ 18.500000][0] IFXUSB: USB core #0 soft-reset[ 18.810000][0] IFXUSB: USB core #0 soft-reset[ 18.810000][0] IFXUSB: ifxhcd_init: req yield ret =9[ 18.810000][0] ifxusb_hcd ifxusb_hcd: IFX USB Controller[ 18.810000][0] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1[ 18.810000][0] ifxusb_hcd ifxusb_hcd: irq 13, io mem 0xbe101000[ 18.810000][0] IFXUSB: Init: Power Port (0)[ 18.810000][0] usb usb1: configuration #1 chosen from 1 choice[ 18.810000][0] hub 1-0:1.0: USB hub found[ 18.810000][0] hub 1-0:1.0: 1 port detected[ 18.810000][0] avm_net_trace: New net trace device 'usb1' registered with minor 161.[ 18.940000][1] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xae3)[ 18.940000][1] {ifx_hsnand_read_page_hwecc} page 0xae3 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 19.000000][1] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x118c)[ 19.000000][1] {ifx_hsnand_read_page_hwecc} page 0x118c Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 19.400000][0] IFXUSB: USB core #1 soft-reset[ 19.740000][0] IFXUSB: USB core #1 soft-reset[ 19.740000][0] IFXUSB: ifxhcd_init: req yield ret =8[ 19.740000][0] ifxusb_hcd ifxusb_hcd: IFX USB Controller[ 19.740000][0] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2[ 19.740000][0] ifxusb_hcd ifxusb_hcd: irq 14, io mem 0xbe106000[ 19.740000][0] IFXUSB: Init: Power Port (0)[ 19.750000][0] usb usb2: configuration #1 chosen from 1 choice[ 19.750000][0] hub 2-0:1.0: USB hub found[ 19.750000][0] hub 2-0:1.0: 1 port detectedIFXUSB HOST started[ 19.750000][0] avm_net_trace: New net trace device 'usb2' registered with minor 162.[ 19.750000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x23db)[ 19.760000][0] {ifx_hsnand_read_page_hwecc} page 0x23db Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-BiterrorDSP: XDU=1( D1 ) OVR=0 MIPS_OVR=0[ 20.360000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2831)[ 20.370000][0] {ifx_hsnand_read_page_hwecc} page 0x2831 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 20.400000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xedf)[ 20.400000][0] {ifx_hsnand_read_page_hwecc} page 0xedf Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 20.420000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xef5)[ 20.420000][0] {ifx_hsnand_read_page_hwecc} page 0xef5 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 20.990000][1] [1]system-load 2 loadavg 0.66 0.15 0.5 - 72 tasks:8 % curr:udevd(0 %) max:udevadm(2 %, pid:540), readytorun: 15, pgfault 1716/s (max 2 avg 1.0)exceute files in group 4 .../etc/init.d/E40-dsl /etc/init.d/E46-net /etc/init.d/E47-voip[ 21.760000][0] [0]system-load 3 loadavg 0.66 0.15 0.5 - 86 tasks:9 % curr:udevd(0 %) max:udevd(1 %, pid:448), readytorun: 10, pgfault 1667/s (max 8 avg 1.1)[dsl sus] dsl line test calib factory file available[dsl get xtse] ANNEX=B DSLMODE=0[dsl get xtse] setting ADSL Annex B/J and VDSL2 oISDN[dsl get xtse] 10 00 10 40 00 04 01 07[dsl sus] diagforce enabled[dsl sus] starting vr9 dsp...[dsl sus] ANNEX=B DSLMODE=0 DIAGNOSE=no[ 22.860000][0] [module-alloc-by-name] give 0x2d000 bytes at 0x81362000 to module 'mei_vr9' (0x5b8000 bytes left)[ 22.860000][0] [module-alloc-by-name] 0x2d000 bytes used, 0x2e094 bytes expected[ 22.920000][0] [dsl_mei] Lantiq (VRX) DSL CPE MEI driver, version 1.4.4, (c) 2013 Lantiq Deutschland GmbH[ 22.920000][0] [dsl mei] tried to set GDBG Level to 4[ 22.920000][0] [dsl mei] debug_level=4, Global UsrDbgLevel=4 MEI_DRV UsrDbgLevel=4 MEI_MEI_ACCESS UsrDbgLevel=4[ 22.920000][0] [dsl mei] debug_level=4, Global IntDbgLevel=4 MEI_DRV IntDbgLevel=4 MEI_MEI_ACCESS IntDbgLevel=4[ 22.920000][0] [dsl_vr9] AVM_MEI_PowerUpDSLSubsystem enable power domain 'DSL + DFE'[ 22.920000][0] [AVM_MEI_PowerUpDSLSubsystem] power up 'PPE TC, PPE EMA, LEDC, DFEV1, DFEV0'[ 22.940000][0] [dsl_vr9] AVM_MEI_PowerUpDSLSubsystem unreset 'DSL, DFE, AFE, VOICE, DSLTC, ARC'spi_clc=0x00000200[dsl sus] loaded vr9 mei driver: mei_vr9.ko with params: , avmDslDiagEnabled=1[ 23.010000][1] [module-alloc-by-name] give 0x4b000 bytes at 0x8138f000 to module 'dsl_vr9' (0x56d000 bytes left)[ 23.010000][1] [module-alloc-by-name] 0x4b000 bytes used, 0x4baf0 bytes expected[dsl drv] Lantiq CPE API Driver version: DSL CPE API V4.16.6-pd1[dsl drv] Predefined debug level: 4[dsl drv] dynamically registered major number 238 for dsl_vr9[dsl sus] loaded vr9 dsl driver: .ko with params:[dsl sus] created vr9 dsl device node /dev/dsl_vr9/0 (major: 238 , minor: 0)[dsl sus] created vr9 mei device node /dev/mei_vr9 (major: 239 , minor: 0)[dsl sus] invoke /sbin/notify_avmnet --broadband_type DSL hw_start_tm_ptm[ 23.200000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1ad0)[ 23.200000][0] {ifx_hsnand_read_page_hwecc} page 0x1ad0 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 23.240000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1b2f)[ 23.240000][0] {ifx_hsnand_read_page_hwecc} page 0x1b2f Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 23.260000][0] [module-alloc-by-name] give 0x27000 bytes at 0x813da000 to module 'ifxmips_ppa_datapath_vr9_e5' (0x546000 bytes left)Loading E5 (MII0/1) driver ......[ 23.310000][0] drivers/net/avm_cpmac/switch/ifx/vr9/ifxmips_ppa_datapath_vr9_e5.c:3243:init_local_variables: [init_local_variables] g_eth_wan_mode=0[ 23.310000][0] drivers/net/avm_cpmac/switch/ifx/vr9/ifxmips_ppa_datapath_vr9_e5.c:3302:init_local_variables: g_wan_itf=0x80, g_wanqos_en=8[ 23.340000][0] CPU_TO_WAN_TX_DESC_BASE[0] =0xbe227400[ 23.340000][1] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown unicast frames 0x68[ 23.340000][1] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown multicast frames 0x68[ppe_e5_init] Succeeded!PPE datapath driver info: Version ID: 64.3.3.1.0.1.1 Family : VR9 DR Type : Normal Data Path | Indirect-Fast Path Interface : MII0 | MII1 Mode : Routing Release : 0.1.1PPE firmware info: Version ID: 7.5.2.11.1 Family : VR9 FW Package: D5 Release : 2.11.1PPE firmware feature: ATM/PTM TC-Layer Bonding Support L2 Trunking Support Packet Acceleration Support IPv4 Support IPv6 Support 6RD Support DS-Lite SupportFIO_MEI_FW_MODE_STAT_GET failed!: Operation not permitted[dsl sus] started dsl_control (configuration: -i10_00_10_40_00_04_01_07 -f/lib/modules/dsp_vr9/vr9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.sh )[ 23.560000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1ffd)[ 23.560000][0] {ifx_hsnand_read_page_hwecc} page 0x1ffd Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 23.570000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x201c)[ 23.570000][0] {ifx_hsnand_read_page_hwecc} page 0x201c Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 23.580000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2023)[ 23.590000][0] {ifx_hsnand_read_page_hwecc} page 0x2023 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 23.610000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2053)[ 23.610000][0] {ifx_hsnand_read_page_hwecc} page 0x2053 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 23.700000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x11a0)[ 23.700000][0] {ifx_hsnand_read_page_hwecc} page 0x11a0 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 23.710000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x20b3)[ 23.710000][0] {ifx_hsnand_read_page_hwecc} page 0x20b3 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 23.720000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x20c6)[ 23.720000][0] {ifx_hsnand_read_page_hwecc} page 0x20c6 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror0[dsl sus] started dsl_monitor[dsl sus] ....vr9 dsp started[ 23.960000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1806)[ 23.960000][0] {ifx_hsnand_read_page_hwecc} page 0x1806 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterroractivating IRQ moderequesting IRQrequest_irqusedIrq: 57 | usedIsrHandler: 81371820 | usedFlags: 0x4000 | pUsedDevName: mei_vr9 | pUsedDevId: -2054024448IRQ requested okMEI_DRV: MEI_IfxRequestIrq(IRQ = 57, .., ), lock = 1check this Cabout to check device statusMEI_DRV[00]: INIT DEVICE, phy addr = 0x1E116000, virt addr = 0xBE116000 IRQ = 57[ 24.150000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x18ad)[ 24.160000][0] {ifx_hsnand_read_page_hwecc} page 0x18ad Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 24.160000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x18ba)[ 24.160000][0] {ifx_hsnand_read_page_hwecc} page 0x18ba Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 24.170000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x18c8)[ 24.170000][0] {ifx_hsnand_read_page_hwecc} page 0x18c8 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 24.180000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x18de)[ 24.180000][0] {ifx_hsnand_read_page_hwecc} page 0x18de Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 24.280000][0] [module-alloc-by-name] give 0x184000 bytes at 0x81401000 to module 'kdsldmod' (0x3c2000 bytes left)[ 24.280000][0] [module-alloc-by-name] 0x184000 bytes used, 0x184a08 bytes expected[ 27.460000][0] kdsldmod: init start (Jul 10 2015 13:44:20) sizeof(struct sk_buff)=440[ 27.470000][0] userman: device registerd (userman_url) with major=232kdsld: ttychannel: ldisc 8 registered[ 27.470000][0] PCP_NL: PCP netlink interface[ 27.470000][0] kdsldmod: init done[ 28.330000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x22aa)[ 28.330000][0] {ifx_hsnand_read_page_hwecc} page 0x22aa Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-BiterrorJan 1 01:00:28 l2tpv3d[1004]: starting.Jan 1 01:00:28 l2tpv3d[1004]: verbose: DISABLED[ 28.480000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x25e0)[ 28.480000][0] {ifx_hsnand_read_page_hwecc} page 0x25e0 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 28.970000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x25c9)[ 28.970000][0] {ifx_hsnand_read_page_hwecc} page 0x25c9 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 29.110000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1504)[ 29.110000][0] {ifx_hsnand_read_page_hwecc} page 0x1504 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 29.130000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2968)[ 29.130000][0] {ifx_hsnand_read_page_hwecc} page 0x2968 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 29.130000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x296a)[ 29.130000][0] {ifx_hsnand_read_page_hwecc} page 0x296a Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 29.150000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2994)[ 29.150000][0] {ifx_hsnand_read_page_hwecc} page 0x2994 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 29.260000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x298c)[ 29.260000][0] {ifx_hsnand_read_page_hwecc} page 0x298c Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 29.360000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x29ed)[ 29.360000][0] {ifx_hsnand_read_page_hwecc} page 0x29ed Sector 1 0 Biterror 0 OOB-Biterror 1 ECC-Biterror[ 29.410000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2904)[ 29.410000][0] {ifx_hsnand_read_page_hwecc} page 0x2904 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 29.420000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2919)[ 29.420000][0] {ifx_hsnand_read_page_hwecc} page 0x2919 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 29.470000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x27b7)[ 29.470000][0] {ifx_hsnand_read_page_hwecc} page 0x27b7 Sector 3 0 Biterror 0 OOB-Biterror 1 ECC-Biterror[avm_power] eth: port 0 force normal CON t0[avm_power] eth: port 1 force throttle CON t0[avm_power] eth: port 2 force throttle CON t0[avm_power] eth: port 3 force throttle CON t0Jan 1 01:00:30 ctlmgr[1010]: WLANLIB: wlan_plugin_init:605: svn revision 2010Jan 1 01:00:30 ctlmgr[1010]: WLANLIB: weak_wlan_check:81: Missing weak 'process_wlanmail'.Jan 1 01:00:30 ctlmgr[1010]: WLANLIB: weak_wlan_check:84: Missing weak 'wlan_enabled_changed'.Jan 1 01:00:30 ctlmgr[1010]: WLANLIB: weak_wlan_check:87: Missing weak 'wlan_wcfgutil_set_output'.Jan 1 01:00:30 ctlmgr[1010]: WLANLIB: weak_wlan_check:88: Missing weak 'wlan_wcfgutil_set_dbg_level'.[ 30.310000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x14da)[ 30.310000][0] {ifx_hsnand_read_page_hwecc} page 0x14da Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 30.320000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x14e1)[ 30.320000][0] {ifx_hsnand_read_page_hwecc} page 0x14e1 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 30.350000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x216a)[ 30.350000][0] {ifx_hsnand_read_page_hwecc} page 0x216a Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 30.350000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x14ee)[ 30.350000][0] {ifx_hsnand_read_page_hwecc} page 0x14ee Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 30.380000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xfc2)[ 30.390000][0] {ifx_hsnand_read_page_hwecc} page 0xfc2 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 30.420000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xfd2)[ 30.430000][0] {ifx_hsnand_read_page_hwecc} page 0xfd2 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 30.460000][1] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x100d)[ 30.470000][1] {ifx_hsnand_read_page_hwecc} page 0x100d Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterrorrc.wlan: Start WLAN...[ 30.930000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x24a2)[ 30.930000][0] {ifx_hsnand_read_page_hwecc} page 0x24a2 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 31.000000][1] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x24c4)[ 31.000000][1] {ifx_hsnand_read_page_hwecc} page 0x24c4 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 31.010000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x24e1)[ 31.010000][0] {ifx_hsnand_read_page_hwecc} page 0x24e1 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-BiterrorWLAND:[01042]:01:00.31/[31.1]:Build = Oct 21 2014 10:59:57[ 31.310000][1] ADDRCONF(NETDEV_UP): lan: link is not ready[ 31.350000][0] [avmnet] [avmnet_mcfw_enable] Device eth1 was enabled already[ 31.360000][0] ADDRCONF(NETDEV_UP): eth1: link is not ready[ 31.390000][0] device eth1 entered promiscuous mode[ 31.590000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1cf6)[ 31.590000][0] {ifx_hsnand_read_page_hwecc} page 0x1cf6 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 31.610000][0] [module-alloc-by-name] give 0x2e000 bytes at 0x81585000 to module 'aae' (0x394000 bytes left)[ 31.610000][0] [module-alloc-by-name] 0x2e000 bytes used, 0x2c688 bytes expected[ 31.810000][0] [wlan_config] Given config is:[ 31.810000][0] [wlan_config] hw_interface=0 chip_type=6 (osprey) offload=1 (non)[ 31.810000][0] [wlan_config] hwrev=203 hwsubrev=1 maca=08:96:d7:3d:9a:c0[ 31.810000][0] [wlan_config] country=276 reg_domain_a=12 reg_domain_b=34[ 31.820000][0] [wlan_eeprom] Calibration data blocks found = 1[ 31.830000][0] [wlan_eeprom] EEPROM #1, type "AR93xx/AR95xx":[ 31.830000][0] [wlan_eeprom] Customer data="AVM7362_CAL1_V1"[ 31.830000][0] [wlan_eeprom] Build with ART2 2.23[ 31.830000][0] avm_net_trace: New net trace device 'WLAN Management Traffic' registered with minor 128.[ 32.060000][0] [avmnet] [avmnet_mcfw_enable] Device eth2 was enabled already[ 32.060000][0] ADDRCONF(NETDEV_UP): eth2: link is not ready[ 32.060000][0] device eth2 entered promiscuous modeJan 1 01:00:32 dsld[1046]: startup ($Revision: 1.160 $$CompileDate: Jul 10 2015 13:43:54 $)Jan 1 01:00:32 dsld[1046]: set_preconfig1Jan 1 01:00:32 dsld[1046]: sync_group in ar7.cfg:Jan 1 01:00:32 dsld[1046]: sync_group:sync_dsl(enabled=1), nr=0Jan 1 01:00:32 dsld[1046]: vcc:1/32Jan 1 01:00:32 dsld[1046]: dsliface:internetJan 1 01:00:32 dsld[1046]: dsliface:voipJan 1 01:00:32 dsld[1046]: sync_group: dslJan 1 01:00:32 dsld[1046]: sync_dsl is igd_deviceJan 1 01:00:32 dsld[1046]: set_preconfig2Jan 1 01:00:32 dsld[1046]: add_vcc_connection: dsl[ 32.280000][0] [module-alloc-by-name] give 0x5000 bytes at 0x815b3000 to module 'adf' (0x38f000 bytes left)[ 32.280000][0] [module-alloc-by-name] 0x5000 bytes used, 0x488c bytes expectedJan 1 01:00:32 dsld[1087]: DSL Mac 08:96:d7:3d:9a:c3Jan 1 01:00:32 dsld[1087]: VOIP Mac 08:96:d7:3d:9a:c4Jan 1 01:00:32 dsld[1087]: VCC2 Mac 08:96:d7:3d:9a:c5Jan 1 01:00:32 dsld[1087]: VCC3 Mac 08:96:d7:3d:9a:c1[ 32.480000][0] [module-alloc-by-name] give 0x3000 bytes at 0x815b8000 to module 'asf' (0x38c000 bytes left)[ 32.480000][0] [module-alloc-by-name] 0x3000 bytes used, 0x326c bytes expected[ 32.520000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2942)[ 32.520000][0] {ifx_hsnand_read_page_hwecc} page 0x2942 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 32.710000][1] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1d8c)[ 32.710000][1] {ifx_hsnand_read_page_hwecc} page 0x1d8c Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 32.740000][0] [avmnet] [avmnet_mcfw_enable] Device eth3 was enabled already[ 32.740000][0] ADDRCONF(NETDEV_UP): eth3: link is not readykdsld: kdsld_vcc_preunregister: *[ 32.740000][0] device eth3 entered promiscuous modeJan 1 01:00:32 dsld[1087]: voip: ppptarget voip disabled, ignored[ 32.750000][0] kdsld: nr_ipv4 0 nr_ipv6 0 nr_vpn 0Jan 1 01:00:32 dsld[1087]: sync_group(prepare_interfaces): dsl: inet_nr=0Jan 1 01:00:32 dsld[1087]: nach prepare_interfaces: dsld.dsliface_default_inet_nr=0, dsld.dsliface_voip_nr=-1Jan 1 01:00:32 dsld[1087]: get_queueindex: none: not foundJan 1 01:00:32 dsld[1087]: queue 0: prio 0 weight 0 shrate 0 shburst 0 wanJan 1 01:00:32 dsld[1087]: queue 1: prio 10 weight 0 shrate 0 shburst 0 wanJan 1 01:00:32 dsld[1087]: queue 2: prio 20 weight 0 shrate 0 shburst 0 wanJan 1 01:00:32 dsld[1087]: queue 3: prio 30 weight 0 shrate 0 shburst 0 wanJan 1 01:00:32 dsld[1087]: queue 4: prio 100 weight 90 shrate 0 shburst 0 wanJan 1 01:00:32 dsld[1087]: queue 5: prio 100 weight 10 shrate 0 shburst 0 wanJan 1 01:00:32 dsld[1087]: queue 6: prio 200 weight 0 shrate 0 shburst 0 wanJan 1 01:00:32 dsld[1087]: appl 0: sip-appl result 1Jan 1 01:00:32 dsld[1087]: classifer: local "localmark sip" result 1Jan 1 01:00:32 dsld[1087]: classifer: local "localmark rtp" result 1Jan 1 01:00:32 dsld[1087]: classifer: local "localmark sip_internet" result 1Jan 1 01:00:32 dsld[1087]: classifer: local "localmark rtp_internet" result 1Jan 1 01:00:32 dsld[1087]: classifer: local "localmark sipdns,ntpdns,tr069dns,tr069" result 2Jan 1 01:00:32 dsld[1087]: classifer: local "localmark igmp" result 3Jan 1 01:00:32 dsld[1087]: classifer: local "localmark webdav" result 4Jan 1 01:00:32 dsld[1087]: classifer: local "localmark dns" result 2Jan 1 01:00:32 dsld[1087]: classifer: lan "udp.dport 43962,47806" result 2Jan 1 01:00:32 dsld[1087]: classifer: lan "ip.proto IPv6-ICMP" result 2Jan 1 01:00:32 dsld[1087]: classifer: lan "ip.proto icmp" result 2Jan 1 01:00:32 dsld[1087]: classifer: lan "udp.dport 53" result 2Jan 1 01:00:32 dsld[1087]: classifer: lan "udp.dport 5060" result 5Jan 1 01:00:32 dsld[1087]: classifer: lan "dhcpoption 12 FRITZ!Media* mediatab" result 6Jan 1 01:00:32 dsld[1087]: classifer: lan "ethsrctab mediatab" result 6Jan 1 01:00:32 dsld[1087]: result 0: tos 65535 vprio 65535 queue 5 appl 65535 bridge 65535 forward 65535[ 32.790000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2723)[ 32.790000][0] {ifx_hsnand_read_page_hwecc} page 0x2723 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-BiterrorJan 1 01:00:32 dsld[1087]: result 1: tos 65535 vprio 65535 queue 2 appl 65535 bridge 65535 forward 65535Jan 1 01:00:32 dsld[1087]: result 2: tos 65535 vprio 65535 queue 1 appl 65535 bridge 65535 forward 65535Jan 1 01:00:32 dsld[1087]: result 3: tos 65535 vprio 65535 queue 0 appl 65535 bridge 65535 forward 65535Jan 1 01:00:32 dsld[1087]: result 4: tos 65535 vprio 65535 queue 6 appl 65535 bridge 65535 forward 65535Jan 1 01:00:32 dsld[1087]: result 5: tos 65535 vprio 65535 queue 2 appl 0 bridge 65535 forward 65535Jan 1 01:00:32 dsld[1087]: result 6: tos 65535 vprio 65535 queue 3 appl 65535 bridge 65535 forward 65535[ 32.920000][1] [module-alloc-by-name] give 0xaa000 bytes at 0x815bb000 to module 'ath_hal' (0x2e2000 bytes left)[ 32.920000][1] [module-alloc-by-name] 0xaa000 bytes used, 0xa7c60 bytes expectedJan 1 01:00:32 dsld[1087]: interface eth3 added.Jan 1 01:00:32 dsld[1087]: interface eth3 up.Jan 1 01:00:32 dsld[1087]: interface lo added.Jan 1 01:00:32 dsld[1087]: interface lo up.Jan 1 01:00:32 dsld[1087]: interface tunl0 added.Jan 1 01:00:32 dsld[1087]: interface sit0 added.Jan 1 01:00:32 dsld[1087]: interface eth0 added.Jan 1 01:00:32 dsld[1087]: interface eth1 added.Jan 1 01:00:32 dsld[1087]: interface eth1 up.Jan 1 01:00:32 dsld[1087]: interface eth2 added.Jan 1 01:00:32 dsld[1087]: interface eth2 up.Jan 1 01:00:32 dsld[1087]: interface ptm_vr9 added.Jan 1 01:00:32 dsld[1087]: interface adsl added.Jan 1 01:00:32 dsld[1087]: interface lan added.Jan 1 01:00:32 dsld[1087]: interface lan up.Jan 1 01:00:32 dsld[1087]: interface guest added.Jan 1 01:00:32 dsld[1087]: start register_vccs_and_ifaces_on_kdsld for sync_dslJan 1 01:00:32 dsld[1087]: setup_dslchannel: ifname=Jan 1 01:00:33 dsld[1087]: kdsld_preregister_vcc: predsl1kdsld: kdsld_vcc_preregister: predsl1kdsld: kdsld_vcc_preregister: vcc->ifaces=(null)Jan 1 01:00:33 dsld[1087]: kdsld_preregister_vcc: kdsld_vccidx=0Jan 1 01:00:33 dsld[1087]: notify_due_to_pmJan 1 01:00:33 dsld[1087]: verbose: DISABLED[ 33.040000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x277d)[ 33.040000][0] {ifx_hsnand_read_page_hwecc} page 0x277d Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 33.050000][1] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)[ 33.080000][1] [module-alloc-by-name] give 0x8000 bytes at 0x81665000 to module 'ath_rate_atheros' (0x2da000 bytes left)[ 33.080000][1] [module-alloc-by-name] 0x8000 bytes used, 0x8098 bytes expected[ 33.120000][1] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved[ 33.160000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1d21)[ 33.160000][0] {ifx_hsnand_read_page_hwecc} page 0x1d21 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-BiterrorJan 1 01:00:33 telefon[1103]: use clock_gettime(CLOCK_MONOTONIC)!Jan 1 01:00:33 telefon[1103]: No S0NT!Jan 1 01:00:33 telefon[1103]: NoOldMSNNames[ 33.190000][1] [module-alloc-by-name] give 0x12000 bytes at 0x8166d000 to module 'ath_dfs' (0x2c8000 bytes left)[ 33.190000][1] [module-alloc-by-name] 0x12000 bytes used, 0x1367c bytes expected[ 33.220000][1] ath_dfs: Version 2.0.0Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reservedmknod: /var/flash/fx_def: File existstelefon: SIGCHLD PID 1110 received!Jan 1 01:00:33 telefon[1103]: WARNING No config file '/var/flash/fx_def' ![ 33.360000][1] [module-alloc-by-name] give 0x5c000 bytes at 0x8167f000 to module 'ath_dev' (0x26c000 bytes left)[ 33.360000][1] [module-alloc-by-name] 0x5c000 bytes used, 0x5b890 bytes expected[ 33.450000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0xbe5)[ 33.450000][0] {ifx_hsnand_read_page_hwecc} page 0xbe5 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 33.480000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x13f6)[ 33.480000][0] {ifx_hsnand_read_page_hwecc} page 0x13f6 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 33.510000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x142c)[ 33.510000][0] {ifx_hsnand_read_page_hwecc} page 0x142c Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 33.530000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1461)[ 33.530000][0] {ifx_hsnand_read_page_hwecc} page 0x1461 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 33.640000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2a3e)[ 33.650000][0] {ifx_hsnand_read_page_hwecc} page 0x2a3e Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 33.650000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2a47)[ 33.650000][0] {ifx_hsnand_read_page_hwecc} page 0x2a47 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 33.680000][1] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved[ 33.680000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1228)[ 33.680000][0] {ifx_hsnand_read_page_hwecc} page 0x1228 Sector 3 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 33.700000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2a6b)[ 33.700000][0] {ifx_hsnand_read_page_hwecc} page 0x2a6b Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 33.780000][1] ADDRCONF(NETDEV_UP): guest: link is not ready[ 33.810000][1] [avmnet] [avmnet_mcfw_enable] Device eth0 was enabled already[ 33.810000][1] ADDRCONF(NETDEV_UP): eth0: link is not ready[ 33.810000][1] device eth0 entered promiscuous mode[ 33.850000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1e45)[ 33.850000][0] {ifx_hsnand_read_page_hwecc} page 0x1e45 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 33.850000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1e50)[ 33.850000][0] {ifx_hsnand_read_page_hwecc} page 0x1e50 Sector 0 1 Biterror 0 OOB-Biterror 0 ECC-BiterrorJan 1 01:00:33 multid[1023]: DHCPD on lan:0 skipped, is virtual interface[ 33.940000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x1e86)[ 33.950000][0] {ifx_hsnand_read_page_hwecc} page 0x1e86 Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-Biterrortelefon: SIGCHLD PID 1120 received!group 4 done ...source files in group 5 ...exceute files in group 5 ...[ 34.150000][1] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x26c8)[ 34.150000][1] {ifx_hsnand_read_page_hwecc} page 0x26c8 Sector 3 0 Biterror 0 OOB-Biterror 1 ECC-Biterrorgroup 5 done ...source files in group 6 ...exceute files in group 6 ...group 6 done ...source files in group 7 .../etc/init.d/S73-capitcp /etc/init.d/S76-media/etc/init.d/S75-inetd /etc/init.d/S78-aha[ 34.380000][1] [module-alloc-by-name] give 0xf7000 bytes at 0x816db000 to module 'umac' (0x175000 bytes left)[ 34.380000][1] [module-alloc-by-name] 0xf7000 bytes used, 0xf7718 bytes expectedJan 1 01:00:34 ctlmgr[1010]: WLANLIB: wland_role_config_init:100: CFG2/API: WLAND configuration file(/var/tmp/wlan_roles) missing.Jan 1 01:00:34 telefon[1114]: NoOldMSNNamesmknod: /var/flash/fx_def: File existstelefon: SIGCHLD PID 1133 received!Jan 1 01:00:34 telefon[1114]: WARNING No config file '/var/flash/fx_def' ![ 35.310000][1] [1]system-load 1 loadavg 1.66 0.39 0.13 - 107 tasks:52 % curr:insmod(7 %) max:ctlmgr(16 %, pid:1010), readytorun: 10, pgfault 2223/s (max 3 avg 1.3)[ 35.310000][0] [0]system-load 4 loadavg 1.66 0.39 0.13 - 107 tasks:0 % curr:cat(0 %) max:upnpd(0 %, pid:1153), readytorun: 11, pgfault 2814/s (max 2 avg 0.7)/etc/init.d/rc.S: /etc/init.d/S76-media: line 6: /etc/init.d/rc.media: not foundJan 1 01:00:35 ctlmgr[1010]: WLANLIB: wland_role_config_init:100: CFG2/API: WLAND configuration file(/var/tmp/wlan_roles) missing.[DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 255 -> 0[DECTDRV_ERR] EepromReadExtRecord, record 0 not found (no records)[DECTDRV_ERR] EepromReadExtRecord, record 0 not found (no records)[ 36.320000][1] ath_pci: 10.2.85 (Atheros/multi-bss)PCI: Enabling device 0000:01:00.0 (0000 -> 0002)__ath_attach: Set global_scn[0]Green-AP : Green-AP : Attachedath_get_caps[6180] rx chainmask mismatch actual 7 sc_chainmak 0ath_get_caps[6155] tx chainmask mismatch actual 7 sc_chainmak 0ic_num_chains=3x3_avm_ath_ext_attach_ah:115_avm_ath_ext_attach_ieee:97ath_attach_dfs[12671] dfsdomain 2[ 36.360000][0] avm_net_trace: New net trace device 'HW (2.4 + 5 GHz, wifi0)' registered with minor 129.[ 36.360000][0] Register net trace device succeeded with minor 129 (wifi0).[ 36.360000][0] wifi0: Atheros ???: mem=0x1c000000, irq=138 hw_base=0xbc000000[ 36.400000][1] [module-alloc-by-name] give 0x6000 bytes at 0x817d2000 to module 'ath_pktlog' (0x16f000 bytes left)[ 36.400000][1] [module-alloc-by-name] 0x6000 bytes used, 0x6654 bytes expected[ 37.540000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x2513)[ 37.540000][0] {ifx_hsnand_read_page_hwecc} page 0x2513 Sector 1 1 Biterror 0 OOB-Biterror 0 ECC-Biterror[ 37.550000][0] [ifx_hsnand_command] read block is critical (status: 0xe8, column: 0x0 page: 0x251f)[ 37.550000][0] {ifx_hsnand_read_page_hwecc} page 0x251f Sector 2 1 Biterror 0 OOB-Biterror 0 ECC-BiterrorJan 1 01:00:37 ctlmgr[1010]: WLANLIB: wland_role_config_init:100: CFG2/API: WLAND configuration file(/var/tmp/wlan_roles) missing.Jan 1 01:00:37 telefon[1114]: Stop DECT[DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 0 -> 0[DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 0 -> 0rc.wlan: Start WLAN...rc.wlan: WLAN daemon already runningexceute files in group 7 ...group 7 done ...source files in group 8 .../etc/init.d/S85-appsexceute files in group 8 ...group 8 done ...source files in group 9 .../etc/init.d/S99-tailrun_clock demon startedAVM_WATCHDOG: System Init UEberwachung abgeschlossen (89300 ms noch verfuegbar)[ 38.600000][1] SysRq : Changing LoglevelLoglevel set to 4Info: have to stop cat /dev/debug.[ 8.460000][0] [module-alloc-by-name] give 0xd000 bytestelefon: SIGHUP received![AHA] SIGHUP receivedpbd[1098]: received signal HangupPlease press Enter to activate this console. Jan 1 01:00:39 ctlmgr[1010]: WLANLIB: wland_role_config_init:100: CFG2/API: WLAND configuration file(/var/tmp/wlan_roles) missing.telefon: SIGCHLD PID 1122 received!telefon: SIGCHLD PID 1192 received!